Strix Nano Goblin – iNAV 2.0.0 Dump
# Features feature PWM_OUTPUT_ENABLE feature AIRMODE feature OSD # Master settings set rssi_channel = 16 #Everyone will be different, this is where I've set mine. set min_throttle = 1035 #You will need to change this when you calibrate your ESC and find the minimum smooth spinning position for your motor. set max_throttle = 2000 set min_command = 1000 set motor_pwm_protocol = MULTISHOT #The Nano Goblin has an ESC that works with MultiShot. Once iNav implements DShot, that will be used instead. set motor_pwm_rate = 2000 #The ESC can use faster updates set servo_pwm_rate = 160 #The servos in the Nano Goblin can also communicate faster set align_board_roll = -95 #Set for the positioning of my flight controller set align_board_yaw = 900 #Set for the positioning of my flight controller set gps_sbas_mode = EGNOS #I set to EGNOS (Europe) for faster lock, but either set to your region or auto. set gps_ublox_use_galileo = ON #Only use if your GPS module supports Galileo satellites. # Fixed Wing set max_angle_inclination_rll = 600 set max_angle_inclination_pit = 600 set small_angle = 180 #Allow arming ant any angle #Return to Home set nav_rth_climb_first = OFF #Climb to altitude as returning home set nav_rth_allow_landing = NEVER #Never land when home point reached, the aircraft will loiter above. set nav_rth_alt_mode = AT_LEAST #Return to home at the MINIMUM altitude specified, if above stay at current height set nav_rth_altitude = 9144 #RTH altitude of 91 metres (300 feet). set nav_rth_home_altitude = 6096 #When arrived at home, lower the altitude to 60 metres (200 feet) set inav_reset_home = FIRST_ARM #Reset the home point when the model is armed for the first time with each plug in. Default is EACH_ARM, but if you accidentally disarm in flight, when you re-arm the home point will be saved there. # General assisted navigation settings. set nav_fw_cruise_thr = 1850 #Will vary dependant on your aircraft, but 1850 seems to be good for the nano, especailly if there's wind. set nav_fw_min_thr = 1200 set nav_fw_max_thr = 2000 #Allow full throttle set nav_fw_bank_angle = 35 set nav_fw_loiter_radius = 4000 #80 metre circle in the sky. set roll_rate = 54 #I measureed the roll rate of my Nano Goblin at 540 degrees a second in Manual mode. set pitch_rate = 22 #I measured the pitch rate of my Nano Goblin at 225 degrees a second in manual mode. #Failsafe set failsafe_recovery_delay = 10 #Allow 1 second to pass before using failsafe. set failsafe_throttle_low_delay = 0 #Never call for failsafe based on the throttle being low, allows for gliding. set failsafe_procedure = RTH # Auto Launch set nav_fw_launch_velocity = 200 set nav_fw_launch_accel = 1700 set nav_fw_launch_max_angle = 180 #Allows the craft to launch at any angle. set nav_fw_launch_detect_time = 30 set nav_fw_launch_thr = 1900 #This is the climb throttle setting and will change depending on the aircraft. set nav_fw_launch_idle_thr = 1000 #Idle throttle of 1000 will mean the prop won't spin until the launch has been detected. set nav_fw_launch_motor_delay = 300 #This will change depending on the aircraft, if there's more chance of your hand hitting the prop, make this number bigger. set nav_fw_launch_spinup_time = 100 set nav_fw_launch_min_time = 0 set nav_fw_launch_timeout = 10000 #10 seconds, the time that auto launch will stay active, climbing the aircraft, before defaulting back to the currently selected mode. set nav_fw_launch_max_altitude = 0 set nav_fw_launch_climb_angle = 25 #The angle at which the aircraft climbs out.