My transmitter setup. A simple guide to a great model

Published by Mr. D on

When you get a new transmitter, there comes a time that you have to move all of your old models to it. However, with my iNav model, I wanted to make a few changes to my transmitter setup. After flying it for a while and creating the OpenTX models for the INAV Fixed Wing Group, I knew some things could be improved upon. So, I thought that creating a video of the process would be a good idea. It must be, as I’ve had a few questions about my transmitter setup.

So I thought I’d create this page to accompany the video, go over things, and add any updates that I make. So this is a simple guide to a great model, which I hope will also help demystify OpenTX.

My Chosen layout

Differences from the video

There are a couple of layout differences from the video. Firstly, I’ve moved launch from SD (middle) to SD (down). So, SD (middle) is now the switch for my LEDs.

Noteworthy features

Flight modes

To change flight modes, I use a combination of switch SA and the 6-way rotary switch S3. This gives me a potential of 8 flight mode, though currently I’m only using 7. The switches are combined as a single input. This means you can only one option at a time, and that they only use up a single RC channel.

Auto-trim, Servo Autotune, LEDs, and Autolaunch

These 4 options are split on to 2 switches, which seem to work like any other. However, They are also a combined input and use a single RC channel. They are on switches SG and SD. SD up is nothing, middle is LEDs on, down is autolaunch. SG up is Auto-trim, middle is off, and down is Servo Autotrim. Curves control the neutral and end points of these switches.

In-flight adjustments

In this OpenTX model, I’ve added an in-flight adjustment OSD for iNav. When you select the 5th OSD option; you can use the throttle and rudder trims to navigate and change the adjustments respectively. I have a video specifically for setting this up here.

Multi-function momentary switch

I have added the multi-function momentary switch to this OpenTX model again. This is a great feature, that will perform different tasks depending on how long you hold in the switch. I have enhanced this further now, by adding voice tracks to inform which task will be performed. Check out my video on the multi-function momentary switch setup here.

iNav 3/4 Update

As new features were added in iNav 3.0, I updated my transmitter setup to use some of these. While I was there, I also made a few changes to switches, and which RC channels are used to communicate with iNav. I won’t go in to this in too much depth, these are the changes I have made. Of course, I’m still using this transmitter layout with iNav 4.

Flight modes

I have slightly revised my flight modes on the 6-way rotary switch. They are now: Acro, Angle, Course Hold, Cruise, Position Hold, and Waypoint Missions.

SG: The tuning switch

I have kept SG as my tuning switch. However, I have removed Servo Autotrim and replaced it with the new Auto Level mode. As far as trimming goes, I will get the plane trimmed and flying well in manual. Then, after physically adjusting the linkages and zeroing the trims on the transmitter, I enable the Continuous Servo Trim feature. I have found this to work very well.

Another change to this is that it no longer uses it’s own RC channel for the tuning modes. I have coupled the switch with switch SF. So that arming and tuning now use channel 5. Both functions are seen separately in iNav.

Launch mode and the LEDs

I have removed launch mode and the LEDs from switch SD. They are now enabled and disabled using the multifunction momentary switch. They are options that aren’t used all the time in flight; so it made more sense to free up SD for things that could change more often.

The camera area

Switches SC and SD are now my camera area. I use these switches to perform functions on the camera. Such as enabling the pan and tilt and head tracker, or switching between multiple cameras.

Share: